Current position > Contact Us
Clamp-on meters, also called clamp-on flow meters, measure liquid flow from the outside of a pipe. There is no cutting, no welding, and no process shutdown. You can install the sensors while the line is live. Send your pipe outer diameter, wall thickness, fluid type, and flow range to get a price.
A clamp-on meter uses ultrasonic sound to read flow through the pipe wall. Two transducers clamp on the outside of the pipe. One sends a signal. The other receives it. The meter calculates flow from the difference in transit time. This works for clean liquids. For dirty or aerated water, a Doppler version is used.
Pipe size can range from DN15 to DN6000. Common pipe materials include stainless steel, carbon steel, PVC, HDPE, and copper. You will need to enter pipe outer diameter and wall thickness. Some models have a sensor spacing tool. Others use a built-in signal check.
Most inline meters need a pipe cut. Clamp-on flow meters do not. This saves labour, welding, and shutdown time. A dairy plant in Malaysia measured CIP return water on stainless pipe. There was no drain and no line stop. A desalination plant in Saudi Arabia added flow measurement on a high pressure brine line. The line stayed in service.
Here is the thing. Engineers like clamp-on meters for temporary checks. They also use them for permanent metering when a line cannot be opened. In practice, you can mount a flow meter in under an hour. Surface prep matters more than the meter itself.
Measure the pipe outside diameter with a tape or caliper. Enter the wall thickness. Select the pipe material and lining if needed. Check the fluid type. Clean water, demineralized water, and chemicals work well with transit time. Sludge, pulp, or raw wastewater may need Doppler.
Typical accuracy is 1 percent of reading for clean liquid on a straight run. Install 10D upstream and 5D downstream if possible. Outputs include 4-20 mA HART, pulse, and RS485 Modbus. Power can be 24 VDC or 85-265 VAC. High temperature transducers handle up to 200 deg C.
Cooling water loops and HVAC systems use clamp-on meters for energy monitoring. Seawater and brine lines use them in desalination. Chemical plants use them on acid, caustic, and solvent transfer lines. Food and beverage plants use them on CIP return, chilled water, and product transfer.
We have seen this on customer sites many times. A paint manufacturer in Southeast Asia used a portable clamp-on meter to check pump flow. The meter paid for itself in one audit. Another customer in Vietnam tested a 300 mm cooling water line before buying a permanent unit.
Silver Automation Instruments sells portable clamp-on flow meters and wall mount clamp-on flow meters. The portable unit works for site audits, pump checks, and leak diagnostics. The wall mount unit works for permanent measurement with 4-20 mA and Modbus. For permanent metering, pair the clamp-on flow meter with a paperless recorder or a PLC.
Mention your pipe size and fluid. We will suggest the right transducer size. Small pipes need a different transducer frequency. Large pipes need a different setup. Most engineers skip this part and then wonder why signal strength is low.
Clean the pipe surface before mounting. Remove paint, rust, and loose scale. Use coupling gel or pads. Strap the transducers tightly. The signal will be stable if the pipe is full. Avoid air pockets, drops, and partially full pipes.
Do not install directly on welds or seams. Keep the sensors away from pumps and valves. A straight run is important. Because the meter reads the velocity profile, swirl can affect accuracy.
Clamp-on meters win when line stoppage is expensive. Inline meters win when accuracy is tight and the fluid has heavy solids or gas. For clean liquids, clamp-on meters provide repeatable measurement. For custody transfer, use a Coriolis or inline electromagnetic meter. For a quick quote, we will ask which one fits your process.
Can a clamp-on flow meter measure gas? No. Most clamp-on ultrasonic meters measure liquids. Gas measurement needs an inline thermal mass or Coriolis meter.
Does pipe material affect accuracy? Yes. Steel, PVC, and copper work well. Concrete or fiberglass may need special transducer frequencies and site testing.
Do I need to stop flow to install? No. You can install clamp-on sensors while the line stays live.
What about rust or scale on the pipe? Clean the pipe surface before mounting. Heavy internal scale can weaken the signal. A Doppler meter may help with entrained solids.
Can it handle corrosive chemicals? Yes. There is no contact with the fluid. The transducer stays outside the pipe. Wetted material compatibility is not an issue.
Send us the pipe outer diameter in mm, wall thickness in mm, fluid type, temperature in deg C, and flow range. We will recommend a clamp-on flow meter and send a price. Silver Automation Instruments is a flow meter manufacturer and supplier. Contact Silver Automation Instruments at Tel +86-25-68650347, WhatsApp +86-25-52155837, or WeChat +86 15365082610.
