Current position > Contact Us
ABB Watermaster units are high-end smart water management distribution network magmeters. They suit remote water distribution sites, DMA zones, and pump stations. If you need a same-accuracy replacement or a lower cost quote for a water network magmeter, send your pipe size and pressure to Silver Automation Instruments.
These are full-bore electromagnetic flow meters. ABB developed the Watermaster range for drinking water, raw water, and irrigation networks. Most units cover DN25 to DN600. Some versions run on internal batteries for years at remote metering chambers. Outputs typically include pulse, 4-20 mA HART, and digital data for SCADA or AMR systems.
The transmitter stores flow data. This helps utilities build district metered area reports. Because water utilities often run unmanned sites, battery life and data logging decide the purchase.
ABB Watermaster units focus on low conductivity water, low flow accuracy, and long service life. The full bore sensor has no moving parts. This matters in raw water with sand or silt. The liner resists wear. Battery powered models suit boreholes, pressure reducing valves, and DMA entry points where AC power is not available.
Most engineers skip the marketing data and check three things. First, the meter must measure bidirectional flow if the DMA has backflow. Second, the transmitter must log data for at least 30 days. Third, the installation should handle occasional flooding. ABB Watermaster units are IP68 rated, but a flooded pit still kills converters if the cable gland is not sealed.
Water utilities in Southeast Asia, the Middle East, Latin America, and Africa install these meters for distribution network monitoring. Typical sites include pump station discharge lines, reservoir inlet pipes, and zone boundary meters. Last year a customer in Vietnam asked us for help after a typhoon flooded a DN150 ABB Watermaster meter chamber. The converter was damaged. The sensor was still usable, but a new ABB transmitter cost more than the whole replacement budget.
We supplied a Silver Instruments electromagnetic flow meter with DN150 PN16 flanges, hard rubber liner, 316L electrodes, and a battery powered converter. The integrator reused the existing straight pipe run. Field start-up took half a day. This is a common replacement path when the original transmitter is obsolete or over budget.
Silver Automation Instruments supplies electromagnetic flow meters for water and wastewater networks. Our range covers DN15 to DN2000. For drinking water, we use hard rubber or EPDM liners and 316L electrodes. Accuracy is 0.5 percent of reading for velocities above 0.3 m/s. We offer 4-20 mA HART, RS485 Modbus, and pulse outputs. Power options include 85-265 V AC, 10-36 V DC, and battery or solar packages for remote sites.
A direct replacement for an ABB Watermaster unit should match the process connection, liner, pressure rating, power supply, and signal output. If you send the existing model code or a photo of the nameplate, our engineers can check dimensions against your pipe schedule. We have done this for EN 1092-1 PN16 and AS4087 PN16 flanges in Australia, Vietnam, the Philippines, and Saudi Arabia.
In practice, many replacement inquiries come from water utility contractors. The original ABB unit is working but the battery pack is dead. Or the project budget cannot absorb the OEM spare part price. Sometimes the customer wants a local supplier with faster delivery. We keep common DN50 to DN300 water magmeters in stock for quick dispatch. Custom liners or large sizes take longer.
One thing to check before ordering any replacement. Measure the internal diameter of the existing pipeline. Some ABB Watermaster sensors have a reduced bore section. If you match only the flange size, you can misjudge flow velocity at low night flows. We can help with sizing if you send normal flow, minimum night flow, and pipe schedule.
Use these specifications when comparing Silver Instruments magmeters with ABB Watermaster units.
Diameter range: DN15 to DN2000
Liner options: hard rubber, PTFE, EPDM, or polyurethane
Electrode options: 316L, Hastelloy C, titanium, or tantalum
Accuracy: 0.5 percent of reading, optional 0.2 percent on request
Output: 4-20 mA HART, RS485 Modbus RTU, pulse, or GPRS
Power: 85-265 V AC, 10-36 V DC, battery, or solar
Protection: IP68 for remote sensor, IP65 for wall mount converter
Pressure: PN10, PN16, PN25, PN40 depending on size
Temperature: 0 to 70 degrees Celsius for rubber liner, up to 120 degrees Celsius for PTFE
Question: What are ABB Watermaster units used for?
Answer: They measure flow in potable water distribution, district metered areas, wellfields, irrigation lines, and pump station discharge pipes.
Question: What sizes do ABB Watermaster magmeters cover?
Answer: Common sizes range from DN25 to DN600. Some network models extend to larger diameters.
Question: Can Silver Instruments replace an ABB Watermaster unit?
Answer: Yes. We supply full-bore electromagnetic flow meters with matching flange ratings and signal outputs. Send the existing model code, pipe size, and flow range.
Question: Do you offer battery powered water flow meters?
Answer: Yes. We can supply battery or solar powered converters for remote water sites with no AC supply.
Question: What details do you need for a quote?
Answer: Pipe size, pressure rating, liner material, power supply, signal output, minimum and maximum flow rate, and fluid type. For replacement, include the ABB nameplate photo if possible.
Send us your pipe size (DN), pressure (bar), temperature (°C), power supply, and flow range. We will reply with price, lead time, and technical datasheet. Contact Silver Automation Instruments:
Tel: +86-25-68650347
WhatsApp: +86-25-52155837
WeChat: +86 15365082610
Website: https://flow-meter.com.au
